Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
We have found this great article relating to Tools You Need to Install a New Bathtub below on the net and reckoned it made good sense to write about it with you on this site.
Mounting a bath tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging job. If the old tub is conveniently accessible, the project can relocate quickly; if you have to open a wall surface to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to move out the old tub as well as set in the brand-new one. Make certain you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed job, it is better to consider using one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This short article will certainly aid you mount a new bath tub in your restroom if you have currently acquired a brand-new tub as well as don't need to change the plan of your previous water pipes.
Your devices and material list need to consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of eliminating the existing taps can be rather problematic due to the restricted access that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in place between the tap and also the sink. Protect the tap in place with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bathtub in the required position. The wooden boards are practical in uniformly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the bath tub till the level reads degree.
To set up taps, fit all-time low of the outermost adaptable tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the supply of water as well as examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bathtub and additionally check the overflow electrical outlet and the regular outlet for leaks.
Lastly, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the tub should wait up until the tub has actually been used at the very least once as this will certainly settle it right into its final placement.
Getting ready for the Installation
Firstly, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to split a rigid seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, bring about problems with moisture as well as feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water before securing, to allow for the activity experienced when the tub is in use. The sealer can split fairly early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads on How to Install a Bathtub Yourself, I imagined sharing that segment was really helpful. So long as you enjoyed reading our blog post plz make sure you remember to share it. I am grateful for your time. Don't hesitate to come visit our site back soon.
Plumbing woes? Contact. Report this page